A Step-by-Step Guide to Setting Up a Tub
A Step-by-Step Guide to Setting Up a Tub
Blog Article
The writer is making several great pointers about Tools You Need to Install a New Bathtub in general in this content following next.
Setting up a tub isn't precisely rocket science, but it does require strong plumbing, woodworking, as well as often, tiling skills. Replacing an old bathtub with a brand-new one is additionally a reasonably tough job. If the old tub is readily accessible, the task can relocate rapidly; if you have to open a wall surface to get rid of the old bathtub as well as position the brand-new bath tub, the job is much harder. In either case, the project is within a residence handyman's skills, although you will require a helper to move out the old bathtub as well as set in the brand-new one. See to it you have qualified on your own for the task and fit trying it. Instead of hiring a service provider to take control of a halfway-completed task, it is much better to think about employing one prior to you start. Possibilities are you may require a specialist plumber to make tube connections.
This short article will aid you set up a new bathtub in your washroom if you have already acquired a brand-new tub and do not require to change the setup of your previous water pipes.
Your devices as well as material list must comprise the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installment, after that the first thing you should do is separate the water system. After doing so, turn on the faucets to drain any kind of water staying in the system. The process of getting rid of the existing taps can be fairly troublesome due to the limited access that is usually the situation.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been removed, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will have to be cleansed of any old securing compound.
Before going on to fit the new faucets, compare the pipe links on the old taps to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the brand-new taps to fit.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will require a plastic adapter to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet and also the other end supplies a link to the existent supply pipelines.
If you require to fit a monobloc, then you will need lowering couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, place the faucet in the mounting hole in the bath/basin making sure that the washing machines are in place between the faucet and also the sink. Secure the tap in position with the supplier provided backnut. Once the tap is safely in place, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal tap adapters. The previous kind must be linked to the faucet ends initially, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Mounting the Bath tub
Making use of both wood boards under its feet, put the tub in the needed setting. The wooden boards are valuable in uniformly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto four tiny factors.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by checking the level and also readjusting the feet on the tub up until the spirit level reads level.
To mount faucets, fit the bottom of the furthest adaptable tap connector to the appropriate supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
Activate the water system as well as inspect all joints and brand-new pipework for leakages as well as tighten them if required. Fill the bath tub as well as likewise check the overflow outlet and also the typical outlet for leaks.
Ultimately, take care of the bath paneling as defined in the maker's instruction manual. Tiling and securing around the tub ought to wait until the bath tub has been used at the very least when as this will resolve it into its final placement.
Getting ready for the Installation
Firstly, the supporting structure supplied with the bathroom ought to be fitted (if called for) according to the maker's instructions. Next off, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is essential to see to it that if the tap features a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps device to prevent stress on the bathtub.
Fit the versatile faucet connectors to the bottom of both taps utilizing 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you use all of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be fitted in its last placement.
Tiling Around the Bathtub
In the location where the bathroom meets the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to fracture a rigid seal, triggering the water to pass through the wall between the bath and also the tiling, leading to problems with moisture and also possible leaks to the ceiling below.
You can pick from a selection of coloured sealants to blend in your fixtures as well as installations. They are marketed in tubes and also cartridges, and also can securing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to always fill up the tub with water before sealing, to enable the motion experienced when the tub is in use. The sealant can break relatively early if you do not consider this motion before sealing.
Additionally, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently offered on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or waterproof adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you liked our section on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks so much for finding the time to read our article. Enjoyed reading our content? Please share it. Help somebody else discover it. Thanks a lot for your time. Please pay a visit to our website back soon.
Get Your Estimate Now
Report this page